How To Reset The NEC Projector Lamp Without a Remote? 9 Steps

Using a projector for routine tasks at home or in the office is going to bring huge innovation to your life. As well as quality when it comes to both your professional work or home entertainment. With all the excitement and comfort of using a projector, you should not forget its maintenance as well. And by maintenance, we mean learning, how to reset the NEC projector lamp without a remote.

All electronic and digital devices require to be taken care of. This will avoid any serious malfunction in the future. So, learning how to reset the projector or how to hard reset NECprojector shouldn’t be a big deal for you.

In this article, we are going to teach you how you can reset your NEC projector lamp without a remote along with some other important information relevant to this topic.

How To Reset The NEC Projector Lamp?

After you have replaced your projector lamp you might notice that your NEC projector lamp is not turning on. This is because you haven’t reset the NEC projector lamp. To reset the projector lamp is one of the vital steps when you replace your projector.

You can reset the NEC projector lamp using both the projector’s remote control and menu buttons. But in this portion, we are only going to explain how to reset the NEC projector lamp with a remote.

So, to reset the NEC projector with a remote follow the steps mentioned below.

Resetting NEC Projector With Remote

  1. Turn on your projector or make sure you set it to standby mode. In short, the projector should not be turned off if you want to reset the lamp.
  2. Now grab the remote controller of your projector and look for the arrow right and left buttons.
  3. Now simultaneously press the arrow right and arrow left buttons.
  4. Meanwhile, hold on to the power button on the panel of your projector.
  5. Keep pressing these three buttons for a few seconds and then release them.
  6. After you are going to release your hold on these buttons the process of lamp reset will be done.
  7. You can now change the lamp and install a new one.

Things To Keep In Mind While Resetting Your Projector’s Lamp

  • You can’t reset your projector lamp while the projector is turned off. So always make sure to turn on the projector. Otherwise, you will face a situation.
  • Also, you can’t reset your projector’s lamp after you have installed a new lamp.
  • Resetting the lamp has to be done before replacing the lamp.

Top 5 Top-Notch Quality Projectors

1. DBPOWER Native 1080P WiFi Projector, Upgrade 9500L Full HD Outdoor Movie Projector, Support 4D Keystone Correction, Zoom, PPT, 300″ Portable Mini Video Projector Compatible w/Phone/Laptop/DVD/TV

2. TMY Projector 7500 Lumens with 100″ Projector Screen, 1080P Full HD Supported Portable Projector, Mini Movie Projector Compatible with TV Stick Smartphone HDMI USB AV, for Home Cinema & Outdoor Movies

3. TMY Mini WiFi Projector 8500 Lumen, 1080P FHD Supported Portable Outdoor Movie Projector Synchronize Smartphone Screen, Compatible with iOS/Android/PC/TV Stick, HDMI USB AV TF, Indoor & Outdoor Use

4. 5G WiFi Bluetooth Projector, Artlii Energon2 Outdoor Projector 4K Supported, FHD Native 1080P, Dolby Audio, Wireless & Wired Mirroring, Home Theater Movie Projector Compatible W/ TV Stick, iOS, Android

5. Native 1080P Projector with WiFi and Two-Way Bluetooth, Full HD Movie Projector for Outdoor Movies, 300″ Display Projector 4k Home Theater, Compatible with iOS/Android/PC/Xbox/PS4/TV Stick/HDMI/USB

How To Reset The NEC Projector Lamp Without a Remote?

If you don’t want to use a remote controller to reset the projector lamp you can reset it without the remote. Resetting the projector lamp without a remote is also followed by certain steps that are as follows;

  1. Make sure your projector is turned on when you are ready to reset it.
  2. Now locate the menu buttons on your projector.
  3. Depending on the type and design of the projector you will find these in different areas on different projectors.
  4. Find the menu buttons until the menu options appear on the screen.
  5. Select the reset menu option from the main menu and press enter.
  6. Now from the reset menu choose the option ‘ Reset Lamp’ or ‘Reset lamp hours’ and press enter.
  7. Or select the yes option.
  8. Your projector lamp will be reset.
  9. Press the Esc key to exit the menu.

Also watch the video shared below:

How Do You Reset The Lamp Hours On An NEC Projector?

No matter how long you have been using an NEC projector is important to reset the lamp hours at some point. Because the NEC projector is designed that way with set lamp hours.

This is not a flaw but it helps you to keep your lamp burning out. Also, the lamp hours remind you to change the lamp to avoid any serious issues with the projector because of the overheating of the old lamp.

We have explained both methods under the title NEC projector reset filter hours below. Give them a read. And follow the one which is more convenient for you.

NEC Projector Reset Lamp Hours With Remote

  • Point the projector’s remote-control right in front of the projector.
  • Locate the Help button and press it for three seconds.
  • No release the help button and press the enter button for three seconds.
  • Repeat the above two steps six times each in case the menu does not appear while pressing each button the first time.
  • The menu will appear on the screen.
  • Now from the menu scroll down to the reset menu.
  • The reset menu will give you two options. Choose the lamp option only.
  • This will reset lamp timings.
  • Now press Esc to exit the menu.

NEC Projector Reset Lamp Hours Without Remote

From the projector’s control panel press the menu button. No from the menu scroll down to the options and choose the default menu and Enter. From the default, the menu chooses the Clear Lamp Hour Meter and presses the enter button. This will reset the lamp user hours.

Also, click the below articles:

Best Projectors For Classroom
Best Lens Cleaners for Projectors
Best Projectors For Sports
Best Projectors For Wedding Receptions
Best Projectors For Ceiling Mounts
Best Projectors For Projection Mapping

How Do You Flip The Image On An NEC Projector?

To flip the image on your NEC projector, perform the following mentioned steps; 

  • Turn your projector on.
  • Now display any image on it.
  • Press the Menu button either from the remote or from the projector control panel.
  • Now scroll down the menu option on the screen and choose the Extended Menu option.
  • From the extended menu select the Projection settings and press the Enter button.
  • Now choose a projection mode that will flip the image back to its real position.
  • Now keep pressing the Esc button until you exit the menu.

How Do You Reset The Lamp Timer On An NEC Projector?

Often people find it difficult to reset the lamp timer on an NEC projector. But believe us it is not as difficult as you might be thinking at this time.

In this article, we have compiled a few easy and short points that are going to save both your time and energy while you work on resetting the lamp timer on an NEC projector.

  • Select the Menu from the projector remote or control panel.
  • From the Menu toggle down to the Reset Menu and press Enter.
  • Now choose the Lamp option from Reset Menu and press Enter
  • This will rest the projector lamp timer.
  • Now press Esc.

You may also like the following articles:

Best Projectors For Halloween Effects
Best Projectors For Cookie Decorating
Best Projectors For Camping
Best Projector For Daytime Use
Best Long Throw Projector For Distance
Best Short Throw Projector For Golf Simulator
Best 1080p Projectors Under 500 Dollars

How Do I Fix My NEC Projector?

You can perform some quick troubleshooting steps to understand the problem and fix your NEC projector. These include;

  • Make sure the projector is properly attached to the power source and there are no faculty cords.
  • Check the projector to see if it’s overheating. In case it is extremely heated shut it off immediately and let it cool down.
  • Check the lamp to see if it is working properly. Replace it if it is old or burnt out.
  • Make sure to check the settings to see if everything is selected properly.

How Do I Fix My NEC Projector Without A Remote?

If you don’t have a remote control no problem. Because you can fix your NEC projector without one. All you have to do is look for the menu buttons on your projector control panels. Press the buttons now the menu will open and show you different options. Choose the relevant option from the menu by pressing Enter and fix the problem you want to resolve.

What Does Status Mean On An NEC Projector?

If your NEC projector status light is blinking red or green it means that your projector is trying to tell you some things. In short, it could be an indication that you have to clean the projector, or the projector is overheating and needs to be cooled off and it could even be a signal for replacing your projector’s lamp.

How Do I Connect My NEC Projector To Wi-Fi?

You can check the NEC projector manual for help. Or you can use an NEC projector app to connect it to the WIFI. We suggest you download the multi-presenter app. Once it is downloaded on your app. Enter the IP number of your projector in this app to connect the projector to WIFI.

How Can You Tell How Many Lamp Hours Are Left On a Projector?

There are two ways you can check the lamp hour status on your projector. The first is to go to the menu and select the information option. If your projector does not have this option. Then another way you can check the hours is by holding onto the on/off buttons for a few seconds. This will display the lamp hours on the screen.

Concluding Remarks

NEC projectors no matter what size, shape, and model they come in are highly equipped with all the modern features. But when it comes to the lamp timing hours or changing the bulb, unlike other projectors you have to rest the projector lamp or the lamp timing hours now and then.

This helps you in not overusing the projector’s lamp or letting it burn out by excessive use. In this article, we have tried our best to provide you with satisfactory answers and information on how to reset your NEC projector lamp without a remote.

We hope you find the information shared above useful and were successful in tackling the issues that you were facing. Good luck and thank you for reading!

For more such informative blogs regarding projectors please visit us more often. Wish you a happy day!

Spread the love

9 thoughts on “How To Reset The NEC Projector Lamp Without a Remote? 9 Steps”

  1. Thank you for your sharing. I am worried that I lack creative ideas. It is your article that makes me full of hope. Thank you.

  2. My spouse and i have been quite delighted Louis could round up his investigation through your precious recommendations he was given in your weblog. It’s not at all simplistic to simply find yourself making a gift of helpful tips which usually others might have been selling. And we all know we’ve got the writer to be grateful to for this. All of the illustrations you’ve made, the easy site navigation, the friendships you will give support to foster – it’s got many incredible, and it’s really facilitating our son and the family imagine that that topic is enjoyable, which is certainly seriously important. Thank you for all!

  3. I want to show my thanks to the writer just for rescuing me from this type of matter. Because of searching through the internet and getting notions which are not pleasant, I assumed my life was done. Being alive minus the approaches to the problems you’ve fixed as a result of your main short article is a crucial case, as well as the kind which might have adversely damaged my career if I had not encountered your blog. The natural talent and kindness in taking care of all areas was very useful. I don’t know what I would’ve done if I had not come upon such a point like this. It’s possible to at this time look ahead to my future. Thanks a lot so much for this expert and result oriented help. I won’t think twice to recommend the website to anybody who should have guide about this subject matter.

  4. I am only commenting to make you be aware of what a nice discovery my girl developed checking your webblog. She even learned lots of details, most notably what it’s like to possess an awesome helping heart to let many others smoothly gain knowledge of selected extremely tough topics. You really surpassed visitors’ desires. Many thanks for supplying those insightful, trusted, revealing and also easy tips about the topic to Sandra.

  5. I wanted to put you that tiny word just to thank you again about the pleasing pointers you have documented on this page. It was simply particularly generous with you to grant unhampered all a lot of folks might have distributed for an e book to end up making some dough on their own, most notably since you could have done it if you considered necessary. The things as well served to be a great way to know that the rest have a similar dream the same as my very own to know significantly more with respect to this condition. I believe there are millions of more pleasurable situations ahead for those who go through your site.

  6. Greetings from Carolina! I’m bored at work so I decided to browse your
    site on my iphone during lunch break. I enjoy the knowledge you provide here and can’t wait to take a look when I
    get home. I’m amazed at how quick your blog
    loaded on my phone .. I’m not even using WIFI, just 3G ..
    Anyhow, wonderful blog!


Leave a Comment